交通运输 / 车辆相关 / 发动机，V型双，4阀头

发动机，V型双，4阀头SolidWorks 三维模型

三维机械图纸名称为：发动机，V型双，4阀头，属于交通运输，车辆相关分类，软件为SolidWorks, 三维模型格式为sldasm,sldprt，可在线预览，可编辑，可供设计参考

平面图
3D视图
发动机，V型双，4阀头主视图
发动机，V型双，4阀头前视图
发动机，V型双，4阀头后视图
发动机，V型双，4阀头左视图
发动机，V型双，4阀头右视图
发动机，V型双，4阀头俯视图
发动机，V型双，4阀头正等轴测图
加入收藏
模型参数

模型ID：10474719

模型大小：111.47M

软件版本： SolidWorks

模型格式：sldasm,sldprt

是否可编辑：可修改，包括参数

上传时间：2026-05-24

图纸介绍：

下载模型
芃芃
作品: 311
粉丝: 0
文件列表
1. 196-A-001 Engine V-Twin 4-Valve-Head GA.SLDASM
21 MB
2. 196-A-002 Cylinder-Head Assembly.SLDASM
6.25 MB
3. 196-A-003 Cylinder-Head (O-Hand) Assembly.SLDASM
6.42 MB
4. 196-A-004 Cylinder Assembly.SLDASM
669 KB
5. 196-A-005 Cylinder (Op-Hand) Assembly.SLDASM
659 KB
6. 196-A-006 Crank-Case Assembly.SLDASM
1.2 MB
7. 196-A-007 Front-Block Assembly.SLDASM
1.5 MB
8. 196-A-008 Front-Case Assembly.SLDASM
1.55 MB
9. 196-A-009 Front Assembly.SLDASM
327 KB
10. 196-A-010 Back-Case Assembly.SLDASM
2.46 MB
11. 196-A-011 Crank-Shaft Assembly.SLDASM
796 KB
12. 196-A-012 Cam-Shaft Assembly.SLDASM
928 KB
13. 196-A-013 Sleeve for Pushrods Assembly.SLDASM
257 KB
14. 196-A-014 Pushrod Inlet Assembly.SLDASM
500 KB
15. 196-A-015 Pushrod Exhaust Assembly.SLDASM
501 KB
16. 196-A-016 Generator Assembly.SLDASM
490 KB
17. 196-A-017 Magnet-Disc Assembly.SLDASM
84.5 KB
18. 196-A-018 Thottle-Bodies Assembly.SLDASM
3.75 MB
19. 196-A-019 Piston Assembly.SLDASM
547 KB
20. 196-A-021 Exhaust-Pipes.SLDASM
508 KB
21. 196-P-001 Crank-Case.SLDPRT
1.11 MB
22. 196-P-002 Front-Block.SLDPRT
579 KB
23. 196-P-003 Front-Case.SLDPRT
585 KB
24. 196-P-004 Front.SLDPRT
343 KB
25. 196-P-005 Back-Case.SLDPRT
435 KB
26. 196-P-006 Crank Starter-Side.SLDPRT
218 KB
27. 196-P-007 Crank Output-Side.SLDPRT
220 KB
28. 196-P-008 Bar for Big-End.SLDPRT
99 KB
29. 196-P-009 Cam-Shaft.SLDPRT
1.14 MB
30. 196-P-010&011 Cylinder-Head.SLDPRT
4.73 MB
31. 196-P-012&013 Cylinder Outer.SLDPRT
1.53 MB
32. 196-P-014&015 Rocker-Box.SLDPRT
838 KB
33. 196-P-016&017 Cover for Rocker-Box.SLDPRT
362 KB
34. 196-P-018 Con-Rod.SLDPRT
135 KB
35. 196-P-019 Clamp for Crank.SLDPRT
101 KB
36. 196-P-020 Sleeve for Cylinder.SLDPRT
98.7 KB
37. 196-P-021 Piston.SLDPRT
358 KB
38. 196-P-022 Piston Ring A.SLDPRT
68 KB
39. 196-P-023 Piston Ring B.SLDPRT
60.1 KB
40. 196-P-024 Piston Ring C.SLDPRT
446 KB
41. 196-P-025 Gidgion Pin.SLDPRT
96.8 KB
42. 196-P-026 Plate for Sump.SLDPRT
242 KB
43. 196-P-027 Plate for Oil-Supply.SLDPRT
140 KB
44. 196-P-028 Plate for Rocker-Axles.SLDPRT
75.9 KB
45. 196-P-029 Axle for Rocker.SLDPRT
95.8 KB
46. 196-P-030 Cover M20x1.5.SLDPRT
202 KB
47. 196-P-031 Drain for Oil.SLDPRT
137 KB
48. 196-P-032 Body for Water-Pump.SLDPRT
328 KB
49. 196-P-033 Rotor for Water-Pump.SLDPRT
204 KB
50. 196-P-034 Cover for Water-Pump.SLDPRT
76.1 KB
51. 196-P-035 Valve Inlet.SLDPRT
69.8 KB
52. 196-P-036 Valve Exhaust.SLDPRT
71.5 KB
53. 196-P-037 Valve-Guide Inlet.SLDPRT
64.1 KB
54. 196-P-038 Valve Guide Exhaust.SLDPRT
69.1 KB
55. 196-P-039 Top for Valve.SLDPRT
146 KB
56. 196-P-040 Collet for Valve.SLDPRT
128 KB
57. 196-P-041 Clamp for Exhaust.SLDPRT
98.1 KB
58. 196-P-042 Collet for Exhaust.SLDPRT
114 KB
59. 196-P-043&044 Rocker Inlet.SLDPRT
300 KB
60. 196-P-045&046 Rocker Exhaust.SLDPRT
307 KB
61. 196-P-047 Extender for Crank.SLDPRT
169 KB
62. 196-P-048 Driver for Pump.SLDPRT
170 KB
63. 196-P-049 Dowel Stepped.SLDPRT
73.9 KB
64. 196-P-050&051 Pushrod.SLDPRT
114 KB
65. 196-P-052 End Lower for Pushrod.SLDPRT
94.2 KB
66. 196-P-053 End Upper for Pushrod.SLDPRT
145 KB
67. 196-P-054 Slider for Pushrod.SLDPRT
140 KB
68. 196-P-055 Backing-Plate for Generator.SLDPRT
343 KB
69. 196-P-056 Former for Generator-Coil.SLDPRT
110 KB
70. 196-P-057 Disc A for Generator.SLDPRT
84.1 KB
71. 196-P-058 Disc B for Generator.SLDPRT
54.7 KB
72. 196-P-059 Cover for Electric.SLDPRT
183 KB
73. 196-P-060 Former for Solanoyd Coil.SLDPRT
115 KB
74. 196-P-061 Inlet-Manifold.SLDPRT
207 KB
75. 196-P-062 Tappet.SLDPRT
66.9 KB
76. 196-P-063 Ball for Tappet.SLDPRT
143 KB
77. 196-P-064 Filler Cap.SLDPRT
99.2 KB
78. 196-P-065 Gear Crank.SLDPRT
262 KB
79. 196-P-066 Gear Output.SLDPRT
377 KB
80. 196-P-067 Gear First for Oil-Pump.SLDPRT
283 KB
81. 196-P-068 Gear Intermediate for Oil-Pump.SLDPRT
356 KB
82. 196-P-069 Gear Large for Oil-Pump.sldprt
298 KB
83. 196-P-070 Gear Driving for Oil-Pump.SLDPRT
277 KB
84. 196-P-071 Gear Driven for Oil-Pump.SLDPRT
254 KB
85. 196-P-072 Gear Starter Large.SLDPRT
431 KB
86. 196-P-073 Gear Starter Intermediate.SLDPRT
323 KB
87. 196-P-074 Gear for Starter-Motor.SLDPRT
141 KB
88. 196-P-075 Gasket for Cylinder-Head.SLDPRT
158 KB
89. 196-P-076 Gasket for Exhaust.SLDPRT
64.8 KB
90. 196-P-077 Gasket for Cylinder-Base.SLDPRT
173 KB
91. 196-P-078 Gasket for Rocker-Box.SLDPRT
285 KB
92. 196-P-079 Gasket for Rocker-Cover.SLDPRT
214 KB
93. 196-P-080 Gasket for Inlet-Manifold.SLDPRT
234 KB
94. 196-P-081 Gasket for Sump.SLDPRT
180 KB
95. 196-P-082 Gasket for Front-Block.SLDPRT
144 KB
96. 196-P-083 Gasket for Front-Case.SLDPRT
191 KB
97. 196-P-084 Gasket for Front.SLDPRT
209 KB
98. 196-P-085 Gasket for Back-Case.SLDPRT
157 KB
99. 196-P-086 Gasket for Pushrods.SLDPRT
196 KB
100. 196-P-087 Gasket for Water-Pump.SLDPRT
203 KB
101. 196-P-088 Gasket forWater-Pump-Cover.SLDPRT
152 KB
102. 196-P-089 Gasket for Oil-Supply-Plate.SLDPRT
213 KB
103. 196-P-090 Gasket for Rocker-Axles-Plate.SLDPRT
265 KB
104. 196-P-091 Throtle-Body Cast.SLDPRT
550 KB
105. 196-P-092 Axle for Throttle-Body.SLDPRT
83.2 KB
106. 196-P-093 Ratchet for Starter.SLDPRT
220 KB
107. 196-P-094 Rod for Solanoyd.SLDPRT
146 KB
108. 196-P-095 Plate for Solanoyd.SLDPRT
74.5 KB
109. 196-P-096 Bracket for Throttle-Bodies.SLDPRT
339 KB
110. 196-P-097 Plate for Oil-Pump.SLDPRT
395 KB
111. 196-P-098 Disk for Throttle-Body.SLDPRT
60.9 KB
112. 196-P-099 Fitting for Oil-Filter.SLDPRT
149 KB
113. 196-P-100 Wheel for Throttle-Bodies.SLDPRT
216 KB
114. 196-P-101 Guide for Pushrods.SLDPRT
335 KB
115. 196-P-102 Screw Special A for Oil.SLDPRT
391 KB
116. 196-P-103 Screw Special B for Oil.SLDPRT
444 KB
117. 196-P-104 Screw Special C for Oil.SLDPRT
486 KB
118. 196-P-105 Screw for Generator.SLDPRT
119 KB
119. 196-P-106 Hose-Tail M16 for 16mm-Pipe.SLDPRT
145 KB
120. 196-P-107 Hose-Tail M20 for 20mm-Pipe.SLDPRT
185 KB
121. 196-P-108 Washer for Big-End-Bearings.SLDPRT
62.7 KB
122. 196-P-109 Washer for Cam-Shaft.SLDPRT
65.7 KB
123. 196-P-111 Washer for Rocker.SLDPRT
61.1 KB
124. 196-P-116 Exhaust-Pipe Set.SLDPRT
410 KB
125. Bearing Needle-Roller 06-15-10.SLDPRT
812 KB
126. Bearing Needle-Roller 12-15-17.SLDPRT
834 KB
127. Bearing Needle-Roller 14-20-17.SLDPRT
452 KB
128. Bearing Needle-Roller 25-31-17.SLDPRT
450 KB
129. Bearing Output Back.sldprt
397 KB
130. Bearing Output Front.sldprt
553 KB
131. Bearing Thrust 10-20-07.SLDPRT
574 KB
132. Bonded-Seal M16.sldprt
318 KB
133. Bonded-Seal M20.sldprt
319 KB
134. Cable Glands Metal.SLDPRT
637 KB
135. Cable for Throttles.SLDPRT
2.88 MB
136. Circlip External.SLDPRT
259 KB
137. Coil for Generator.SLDPRT
183 KB
138. Coil for Solanoyd.SLDPRT
88.9 KB
139. Fitting umi_-_06_x_je_813_s.SLDPRT
118 KB
140. Fitting umi_-_08_x_je_813_s.SLDPRT
118 KB
141. Injector Aprilia 450 SXV.SLDPRT
466 KB
142. Jubilee Clip for 44.SLDPRT
1.12 MB
143. Key 10x6x25.SLDPRT
53.5 KB
144. Key 12x8x12-R.SLDPRT
53 KB
145. Key 5x5x15-R.SLDPRT
54.1 KB
146. Locking Washer, M12, MB_1_2_14b.SLDPRT
148 KB
147. Locking Washer, M25, MB_5_2_14b.SLDPRT
148 KB
148. Locking Washer, M30, MB_6_2_14b.SLDPRT
162 KB
149. Locking Washer, M35, MB_7_2_14b.SLDPRT
146 KB
150. Locking Washer, M40, MB_8_2_14b.SLDPRT
162 KB
151. Locknut, M25x1.5, KM_5_2_14b.SLDPRT
173 KB
152. Locknut, M30x1.5, KM_6_2_14b.SLDPRT
119 KB
153. Locknut, M35x1.5, KM_7_2_14b.SLDPRT
129 KB
154. Locknut, M40x1.5, KM_8_2_14b.SLDPRT
171 KB
155. Magnet Misumi HXNH 15_5.SLDPRT
121 KB
156. Magnet Misumi HXNH 6_10.SLDPRT
103 KB
157. NJ 2306 ECML.SLDASM
322 KB
158. Nut Full SS.SLDPRT
315 KB
159. Nut Half SS.SLDPRT
1.44 MB
160. Nut, Castle, M6, DIN935.SLDPRT
183 KB
161. Nut, Castle, M8, DIN935.SLDPRT
131 KB
162. O-Ring 18x2.65.SLDPRT
170 KB
163. O-Ring 9-1.8.SLDPRT
179 KB
164. O-Ring for Cover.SLDPRT
153 KB
165. Oil Filter.SLDASM
1.96 MB
166. Oil-Seal-RSC-01001806-ComTech.sldprt
131 KB
167. Oil-Seal-RTC-01602407- ComTech.sldprt
583 KB
168. Oil-Seal-RTC-01802807-ComTech.sldprt
139 KB
169. Oil-Seal-RTC-03004007-ComTech.sldprt
126 KB
170. Pin 3x20.SLDPRT
65.3 KB
171. Pin for Piston.SLDPRT
145 KB
172. Pin for Pushrod.SLDPRT
148 KB
173. Pipe 1 for Cooling.SLDPRT
142 KB
174. Pipe 1 for Oil.SLDPRT
103 KB
175. Pipe 2 for Cooling.SLDPRT
149 KB
176. Pipe 2 for Oil.SLDPRT
88.1 KB
177. Pipe 3 for Oil.SLDPRT
85.7 KB
178. Plain Bearing Igus.SLDPRT
139 KB
179. SNGE 17-400.00.SLDASM
599 KB
180. SNGE 17-401.00.SLDPRT
402 KB
181. SNGE 17-402.00.SLDPRT
295 KB
182. SNGE 17-403.00.SLDPRT
262 KB
183. SNGE 17-404.00.SLDPRT
186 KB
184. SNGE 17-405.00.SLDPRT
150 KB
185. SNGE 17-406.00.SLDPRT
66.6 KB
186. SNGE 17-407.00.SLDPRT
157 KB
187. Screw M10 Cap-Hd SS.SLDPRT
1.97 MB
188. Screw M2.5 Pan-Hd SS.SLDPRT
285 KB
189. Screw M4 Cap-Hd SS.SLDPRT
285 KB
190. Screw M4 Pan-Hd SS.SLDPRT
335 KB
191. Screw M5 Cap-Hd SS.SLDPRT
543 KB
192. Screw M6 Cap-Hd SS.SLDPRT
611 KB
193. Screw M8 Cap-Hd SS.SLDPRT
341 KB
194. Split Pin M6.SLDPRT
145 KB
195. Split Pin M8.SLDPRT
154 KB
196. Spring Inner for Valve.SLDPRT
1.05 MB
197. Spring Outer for Valve.SLDPRT
797 KB
198. Spring Starter.SLDPRT
1.36 MB
199. Standoff Hex M-F Steel.SLDPRT
134 KB
200. Starter Motor.SLDPRT
270 KB
201. Washer M6 Copper.SLDPRT
98 KB
202. Washer M8 Copper.SLDPRT
85.1 KB
203. Washer Mudguard SS.SLDPRT
130 KB
204. Washer Plain SS.SLDPRT
153 KB
205. Washer Spring SS.SLDPRT
307 KB
206. _NJ 2306 ECML_PART1.sldprt
180 KB
207. _NJ 2306 ECML_PART2.sldprt
204 KB
208. _NJ 2306 ECML_PART3.sldprt
95.9 KB
209. filter.SLDPRT
498 KB
210. kate1.SLDPRT
247 KB
211. kate2.SLDPRT
1.45 MB
212. klapp.SLDPRT
61.6 KB
213. korpus.SLDPRT
728 KB
214. tihend.SLDPRT
102 KB
215. vedru.SLDPRT
655 KB
216. v鋜e.SLDPRT
39.9 KB
【发动机，V型双，4阀头】相关作品
下载提示
×

下载该图档需要消耗20金币！

确认下载
-- 热门充值套餐 · 限时优惠 --
更多套餐 ❯
Copyright © 2019-2026 www.shanhu3d.com 珊瑚网 All Rights Reserved. 皖ICP备17011993号